SNFUtility/SNFMilterConfig/SNFMilterConfigTests.txt

			SNFMilterConfig Tests

$Id$

SNFUtility revision 9

Help functionality
------------------

HELP-01: SNFMilterConfig without any command options outputs a help
message.

  Result:  Pass.


Conflict detection
------------------

CONFLICT-01: Run with -setup, -id, and -auth.  Verify that help
message is output, and that SNFMilterConfig takes no action.

  Result:  Pass.

CONFLICT-02: Run with -setup and -start.  Verify that help message is
output, and that SNFMilterConfig takes no action.

  Result:  Pass.

CONFLICT-03: Run with -setup and -stop.  Verify that help message is
output, and that SNFMilterConfig takes no action.

  Result:  Pass.

CONFLICT-04: Run with -setup and -mta=XXX, where XXX is postfix,
sendmail, and none.  Verify that help message is output, and that
SNFMilterConfig takes no action.

  Result:  Pass.

Setup/Repair functionality
--------------------------

SETUP-01: Start with no configuration files installed (SNFMilter.xml,
identity.xml GBUdbIgnoreList.txt, and getRulebase).  Verify that
either "-setup" or "-repair" creates these files with the default
credentials.

  Result:  Pass.

SETUP-02:  Repeat SETUP-01 with -v and verify that files are created.

  Result:  Pass.

SETUP-03:  Repeat SETUP-01 with -explain and verify that files are not created.

  Result:  Pass?  Exception thrown (as expected) when attempting to read
  configuration file that doesn't exist.

Config file specification
-------------------------

CONF-01: Start with no configuration files, and copy the sample
configuration file to test.xml.  Run with "-setup -config=test.xml",
and verify that all configuration files except
/etc/snf-milter/SNFMilter.xml are created.

  Result:  Pass.

CONF-02:  Repeat with -v and verify the same behavior.

  Result:  Pass.

CONF-03:  Repeat with -explain.

  Result:  Pass.

Credential Functionality
------------------------

CRED-01: Configure, and run "-id=xxx -auth=yyy" with specification of
incorrect credentials.  Verify:

  1) getRulebase is not updated, and getRulebase.failed file is
     created.,

  2) The rulebase downloaded fails, and an error message is output,

  3) The identity.xml file is not changed.

  Result:  Pass.

CRED-02:  Repeat CRED-01 with -v and verify correct operation.

  Result:  Pass.

CRED-03:  Repeat CRED-01 with -explain and verify correct operation.

  Result:  Pass.

CRED-04: Install default configuration files.  Modify identity.xml as
follows:

  1) Change the license ID to "XXX" and authentication to "YYY".

  2) Add a comment.

Then run with "-id=testmode -auth=setuptestingonly".  Verify:

  1) getRulebase is updated, and the new rulebase is downloaded.

  2) identity.xml has only the license ID and authentication updated.

  Result:  Pass.

CRED-05: Repeat CRED-04 with -v and verify correct operation.

  Result:  Pass.

CRED-05: Repeat CRED-04 with -explain and verify correct operation.

  Result:  Pass

Start/stop functionality with XCI enabled
-----------------------------------------

START_STOP_XCI-01: Install default configuration files, and ensure
that SNFMilter is stoped.  Create a configuration file
SNFMilter_xci.xml as follows:

  1) Enable XCI.

  2) Enable status.second logging, with no append.

  3) Enable status.minute logging, with append.

Do the following, specifying the configuration file SNFMilter_xci.xml:

  1) Run SNFMilterConfig with "-start", and verify that SNFMilter starts.

  2) Run SNFMilterConfig with "-start" again and verify that SNFMilter
     is not started again.

  3) Run SNFMitlerConfig with "-stop" and verify that SNFMilter stops.

  4) Run SNFMitlerConfig with "-stop" again and verify that SNFMilter
     is not stopped again.

  Result:  Pass

START_STOP_XCI-02: Repeat START_STOP_XCI-01 but with "-v" in the command-line.

  Result:  Pass

START_STOP_XCI-03: Configure as for START_STOP_XCI-01, and do the following:

  1) Run SNFMilterConfig with "-start -explain".  Verify correct
     output, and that SNFMilterConfig doesn't start SNFMilter.

  2) Run SNFMilterConfig with "-stop -explain".  Verify correct
     output, and that SNFMilterConfig doesn't stop SNFMilter.

  3) Start SNFMilter.

  4) Run SNFMilterConfig with "-start -explain".  Verify correct
     output, and that SNFMilterConfig doesn't start SNFMilter.

  5) Run SNFMilterConfig with "-stop -explain".  Verify correct
     output, and that SNFMilterConfig doesn't stop SNFMilter.

  Result:  Pass

Start/stop functionality with XCI disabled, status.second enabled
-----------------------------------------------------------------

START_STOP_SEC-01: Install default configuration files, and ensure
that SNFMilter is stoped.  Create a configuration file
SNFMilter_second.xml as follows:

  1) Disable XCI.

  2) Enable status.second logging, with no append.

  3) Enable status.minute logging, with append.

Do the following, specifying the configuration file SNFMilter_second.xml:

  1) Run SNFMilterConfig with "-start", and verify that SNFMilter starts.

  2) Run SNFMilterConfig with "-start" again and verify that SNFMilter
     is not started again.

  3) Run SNFMitlerConfig with "-stop" and verify that SNFMilter stops.

  4) Run SNFMitlerConfig with "-stop" again and verify that SNFMilter
     is not stopped again.

  Result:  

START_STOP_SEC-02: Repeat START_STOP_SEC-01 but with "-v" in the
command-line.

  Result:  

START_STOP_SEC-03: Configure as for START_STOP_SEC-01, and do the
following:

  1) Run SNFMilterConfig with "-start -explain".  Verify correct
     output, and that SNFMilterConfig doesn't start SNFMilter.

  2) Run SNFMilterConfig with "-stop -explain".  Verify correct
     output, and that SNFMilterConfig doesn't stop SNFMilter.

  3) Start SNFMilter.

  4) Run SNFMilterConfig with "-start -explain".  Verify correct
     output, and that SNFMilterConfig doesn't start SNFMilter.

  5) Run SNFMilterConfig with "-stop -explain".  Verify correct
     output, and that SNFMilterConfig doesn't stop SNFMilter.

  Result: